Robotics COURIER Informations techniques Page 14
- Page / 151
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Introduction 1-5
x2 56-kbps Connectivity
If you have enabled x2, your Courier can connect at speeds up to
56 kbps. While line conditions may not always allow for 56 kbps
connections, the new Courier software allows you to achieve the fastest
analog speeds available.
Adaptive Speed Leveling to Adjust to Line Conditions
Adaptive Speed Leveling® (ASL) allows your Courier to monitor line
conditions while connected, and fall back to the next lower speed if
conditions are poor. Couriers also detect improved line conditions and
shift upward to the next higher speed. The transmit and receive channels
adapt independently, each detecting and adjusting to line conditions.
Calls to and from Modems and Fax Machines
When used with fax-capable communications software, your Courier
auto-detects and responds to calls from modems and Group III fax
machines using EIA-standard Class 1 or 2.0 fax software.
Data CompressionV.42 bis/MNP5
Data compression enables throughput of up to 230.4 kbps on analog
connections. I-modems connecting under V.42 or HST error control use
V.42bis compression. I-modems connecting under MNP error control use
MNP Level 5 compression. Typically, files can be compressed from 2:1 to
4:1.
Error ControlV.42/MNP
Data integrity is ensured when the I-modem connects with remote devices
that use the V.42 (LAPM), HST, or MNP error control protocols. Error
control is available on analog calls at 1200 bps and above.
V.Everything
The Courier provides full support of the x2, V.34 standard, V.Fast Class,
V.32 terbo, and many other modulation schemes, spanning the range of
speeds between 300 bps and 56 kbps.
- Courier™ I-modem® 1
- Getting Started Guide 1
- Final Draft 1
- Read this First 3
- Contents 4
- Chapter 1 10
- Introduction 10
- Optional Built-in NT-1 12
- Optional Analog Device Jack 12
- TurboPPP 12
- Rate Adaptation 12
- Chapter 2 16
- The I-modem and ISDN 16
- What is ISDN? 17
- Benefits of ISDN 17
- The ISDN Basic Rate Interface 17
- Physical Appearance 17
- B-channels and D-channels 18
- Required Components 19
- How Does the I-modem Fit In? 19
- S/T Interface 20
- Internet Access (TurboPPP) 21
- Chapter 3 24
- Ordering ISDN Service 24
- Requesting ISDN Service 25
- Chapter 4 28
- Installing Your 28
- Internal I-modem 28
- Package Contents 29
- Important! 30
- Default Jumper Settings 31
- Windows 95 Users 32
- I-modem Model S/T 37
- 1 Run HyperTerminal 38
- 4 Change any properties and: 40
- Chapter 5 43
- External I-modem 43
- ISDNTelephone 45
- Chapter 6 47
- Service Profile Identifiers 48
- Terminal Endpoint Identifier 48
- Configuring the I-modem 49
- Chapter 7 57
- Configuring With 57
- AT Commands 57
- Preparing to Send AT Commands 58
- 4 Set up the DATA B-channel 61
- 2 Make a test data call 64
- Analog Device Port 65
- Data Port 65
- Chapter 8 67
- Configuring Your Courier 67
- For Windows 95 67
- Files Needed By Your I-modem 70
- If Dial-Up Networking Do this 72
- Support” to install Dial-Up 72
- Networking 72
- Is not listed Go to Step 3 72
- 4 Click Windows Setup tab 73
- 7 Click OK 74
- Windows 95 8-9 75
- Settings” 76
- 7 Click Finish 79
- 9 Click OK, and OK 79
- Windows 95 8-15 81
- TCP/IP Settings window 81
- Chapter 9 83
- Configuring Your 83
- I-modem For Macintosh 83
- 2 Click PPP and More… 84
- Configuring ConfigPPP Dialer 85
- Dialing With ConfigPPP 85
- Chapter 10 87
- What You Need 88
- Configuring Your I-modem 88
- If You Are Using MS-DOS 89
- For Internal Couriers Only 89
- If You Are Using OS/2 90
- Chapter 11 93
- Configuring TurboPPP 93
- With AT Commands 93
- Making Calls With ML-PPP 94
- Connection With ML- PPP 95
- Pass-through Compression 98
- Auto Mode Compression 98
- Turbo Mode Compression 98
- Chapter 12 101
- Configuring Your I-modem 101
- With DIP Switches and Jumpers 101
- Default DIP Switches 104
- Locating DIP Switches 104
- Locating Jumpers 105
- Changing Jumper Settings 106
- Chapter 13 108
- Viewing LEDs 108
- Viewing LEDs 13-3 110
- Chapter 14 111
- Using x2 111
- Obtaining x2 112
- How x2 Works 113
- Controlling x2 113
- x2 Server Mode 113
- Controlling Link Speeds 114
- New x2 Result Codes 118
- Numeric Alphanumeric 119
- I-modem Command Reference 120
- Appendix A 121
- Other I-modem Features 121
- Period Dial Modifier 122
- PCSDL vs. XMODEM 122
- Forcing Analog Calls 123
- Appendix B 125
- Technical Information 125
- Modulation 126
- Additional Specifications 128
- Ringer Equivalence 129
- Power Consumption 129
- Serial Ports 129
- The EIA-232 Interface 130
- Minimum Requirements 131
- Flow Control Requirements 131
- For Macintosh Computers 132
- I-modem’s serial port: 133
- Choosing a Serial Cable 135
- Notes for Macintosh Users 135
- Notes for Mainframe Users 136
- Macintosh 136
- Appendix D 137
- Warranty 137
- Telephone Support 140
- North America 140
- Europe, Middle East, Africa 140
- All Other Locations 140
- Software/Firmware Updates 141
- Hardware Support 141
- FCC Registration 143
- IC (Industry Canada) 144
- UL Listed Accessory 145
Sanyo PLC-XF70 manuály
Uživatelské manuály a uživatelské příručky pro Projektory Sanyo PLC-XF70.
Poskytujeme 1 manuály pdf Sanyo PLC-XF70 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commentaires sur ces manuels